Committed to creating low-cost, high-quality, high-efficiency boiler products.
Rated evaporation: 1-20 tons
Thermal efficiency: 100-104%
Application: Food factory, hospital, paper mill, textile factory, building material factory,etc.
Rated thermal power: 0.7-14Mw
Thermal efficiency: 96-98%
Fuel: light oil, gas,coal,electric,etc.
Application: Industrial areas requiring large amounts of hot water or heating supply
Rated thermal power: 2.8-7.0Mw
Rated thermal efficiency: ≥105.5%
Fuel: natural gas
Application: Enterprises, institutions, office buildings, etc.
Rated evaporation: 2-25 tons
Rated thermal efficiency: ≥84%
Application: Food mills, textile mills, paper mills, pharmaceutical factories, wood factories, breweries, rubber factories, chemical plants, etc.
Rated evaporation: 2—10 tons
Rated thermal efficiency: ≥80%
Application: Food factory, hospital, paper mill, textile factory, building material factory, rubber factory, pharmaceutical factory, food factory,etc.
Thermal capacity:7000-29000 KW
Thermal efficiency: ≥95%
Application: Building materials industry, feed industry, rubber factory, textile factory, food factory, etc.
• Cycle Injection of CO2 in Heavy Oil in Comparison with Steam Injection • Results C02 Cycle Injection in Louisiana State, USA. • Summary • References. Topic 8: NEW METHODS IN THERMAL RECOVERY. Objective: To study the new technology in thermal recovery applied in Heavy and extra-heavy Oils. 1.VIEW DETAIL
Steam recovers light and heavy oil and can be utilized in oil fields. Cyclic injection (Huff N Puff) Cyclic Steam Stimulation also known as "Huff-and-Puff" assists natural reservoir energy by lowering the viscosity of oil . Commonly used for a formation of oil-wells but can be applied to a single oil well.VIEW DETAIL
Steam Injection Recovery for Thin-bedded Heavy Oil Reservoir in Shallow Wells Steam injection recovery is an efficient method for heavy oil recovery, and steam assisted gravity drainage (SAGD) is a specificVIEW DETAIL
2016-8-3 · For steamflood operations, some wells are used for injection and others are used for production. During the steamflood, high-quality steam is injected into the heavy-oil reservoir; steam heats the oil and pushes it toward a producing well. As opposed to the CSI, during the steamflood, two mechanism are involved in the recovery process.VIEW DETAIL
Ultra-high pressure steam injection technology: Product introduction: For development of deep heavy oil, DESHI GROUP has a 35MPa supercritical high-pressure steam injection boiler. The application is that steam injection under ultra-high pressure, high temperature, less than 6100 meters deep well heavy oil and super heavy oil.VIEW DETAIL
Alibaba.com offers 6,926 heavy oil steam boilers products. About 99% of these are boilers. A wide variety of heavy oil steam boilers options are available to you, such as natural circulation, once through.VIEW DETAIL
Steam boiler feed water pump-boiler feed water pump It is usually driven by electric motor or diesel engine and especially designed for pumping the hot water and hot water with steam. Typical applications includes steam injection boiler for oil field, heavy oil thermal recovery, high pressure hot water application, high pressure steamVIEW DETAIL
Additionally, you won't run into the dangers caused by steam trap issues, or by freezing steam since hot oil's freezing point is significantly lower than water's. 8. Hot Oil Heating Systems Require Less Capital Than Steam Systems. Hot oil heating systems typically require less capital than boiler systems as they are significantly simpler.VIEW DETAIL
China Gas Steam Boiler manufacturers - Select 2020 high quality Gas Steam Boiler products in best price from certified Chinese Boiler manufacturers, Oil Boiler suppliers, wholesalers andVIEW DETAIL
Heavy oil can be produced in limited amounts by "cold" production, with typical recovery factors in the range of 5% to 8%. SDS Steam Units allow drillers to heat the reservoirs by method of steam injection, which typically boosts recovery rates to well over 20%, and in some cases as high as 70%.VIEW DETAIL
This tool will be used to support the preparation of a HiTAC boiler field test. This field test will be done at 9 MW scale by Stork Thermeq, using heavy oil characterized and delivered by Shell. Stork will also develop water-steam cycles optimized for application in combination with HiTAC combustion.VIEW DETAIL
Cite this article: Liu Yuwen,Xu Hongguo. Estimation Study of the Efficiency of the Steam Injection System in Thermal Recovery of Heavy OilJ. Journal of Liaoning Shihua University, 2014, 34(3): 62-66.VIEW DETAIL
Water/Steam Injection. Water or steam injection can be utilized to reduce NOx levels. By injecting water or steam into the flame, flame temperatures are reduced, thereby lowering thermal NOx formation and overall NOx levels. Water or steam injection can reduce NOx up to 80% (when firing natural gas) and can result in lower reductions whenVIEW DETAIL
Superheated steam huff and puff was put into Kazakstan's heavy oil reservoir after saturated steam huff and puff and the average daily oil production was 2-4 times that of saturated steam huff and puff, which improved heavy oil production effectively.VIEW DETAIL
The production of extra-heavy oil or bitumen using the steam-assisted gravity-drainage (SAGD) method entails the generation and injection of a large quantity of steam into the reservoir.VIEW DETAIL
2018-10-1 · The steam injection boiler for oil field is the main equipment for heat thick oil recovery, the key part of which is a burner.,。VIEW DETAIL
Typical steam/oil ratio values for the production of extra heavy oil or bitumen using the SAGD method are between 2 and 4. This implies that the production of one barrel of bitumen requires the injection of 2 to 4 bcwepd (barrels of cold water equivalent per day) of steam, and that a similar quantity of hot water is produced together with the oil.VIEW DETAIL
Steam-Oil Ratio: The steam-oil ratio (SOR) is a metric used to quantify the efficiency of oil recovery processes based on types of steam injection. The steam-oil ratio measures the volume of steamVIEW DETAIL
2010-7-8 · Steam injection into deep underground formations has proven to be an effective method for EOR facilities producing heavy oil from an oil-sand formation. It is typically done through SAGD, Steam Drive or by CSS. In recent years, the SAGD method has become more popular, especially for heavy oilVIEW DETAIL
2017-5-4 · § Heavy Oil, Extra Heavy Oil, Oil Sands, Tar Sands, Bitumen, . Ł need for a simple classification 4 Classes based mainly on downhole viscosity : 0A Class : Medium Heavy Oil 25°gt; d°API gt; 18° 100 cPo gt;m gt; 10 cPo, mobile at reservoir conditions 0B Class : Extra Heavy Oil 20°gt; d°API gt; 7° 10 000 cPo gt;m gt; 100 cPo, mobile at reservoirVIEW DETAIL